Der Einkaufswagen hat einen Nachfolger
Enduro für Flitzi - Ist n KTM 390 Adventure geworden
- Tobiker
- Erledigt
-
-
Wird das Ding mit 6 Schrauben montiert, an der Seite hatte ich jetzt gar keine gesehen?!
-
So sieht das Ding aus.
Im Moment sehe ich passend zugeschnitten Alubutyl, reingepappt. Dann ist sicher ruhe solange das Zeug nicht weggelaufen ist.Oder gleich die Befestigung (Stahl, schwarz) auch noch runter nehmen und den Töff nur noch als Strassengerät verwenden.
-
Der Einkaufswagen hat einen Nachfolger
Hilf mir mal, ich hab ja Humor...
-
Gist es noch Befestigungsmaterial.....es gibt für die originale nur 4 Befestigungen ( Honda crf300) .
-
Das Drama spielt sich am 390 Adventure ab.
-
Tobiker
Hat den Titel des Themas von „Enduro für Flitzi“ zu „Enduro für Flitzi - Ist n KTM 390 Adventure geworden“ geändert. -
berührt das blech den auspuff?
-
Nein. Hat 2-3mm dazwischen.
Im Moment würde ich das Ding einfach weglassen, ev. das Original wieder dran denn das deckt auch ein wenig ab und viel Offroad mache ich wohl nicht mit dem 390er.
-
Willst du im Fun-Park oder am Bellevue die Treppengeländer runtergrinden oder was hast du vor mit dem Schutz?
-
Der Einkaufswagen hat einen Nachfolger
Hilf mir mal, ich hab ja Humor...
Es gab hier einmal einen nicht ganz unbekannten Töff, der schepperte wie ein Einkaufswagen, wenn über das kleinste Hindernis *) holperte. Mit einem wagemutigen Eingriff konnte das dann abgestellt werden.
*) ab Grösse Sandkorn aufwärts
-
Wo hast du den Givi Motorschutz gekauft? Louis z.B. ist äusserst grosszügig bei Rückgaben!
-
https://www.motoin.de
Ist ne Variante. Nur muss ich vorher die gebrochene Stahlhalterung (Verbindung zum Motor) schweissen.
Wurde gestern von Sachsi bemerkt als wir beim Grillen ein anderes Thema gesucht haben als "Altersgebrechen". -
Anfänger-Flitzi...
Die Stahlhalterung wäre doch nicht gebrochen. Die Aluhalterung hingegen schon. Also 1 x Neu, oder kann grad wer Alu Schweissen?Dann lasse ich doch gleich noch die neuen Reifen aufziehen, die Alten kommen irgendwie sehr schnell an die Verschleissgrenze, dabei fahre ich doch kaum.
-
Die Motorschutz Halterung ist geschweisst, in die Wanne hab ich par Löcher gemacht und jetzt frage ich mich, ob ev. ein par viele Silikonstellen (Einfach Sanitärsilikon "Haufen" reinkleben die eigenschwingungen effektiv verhindern könnten. Zu nah am Auspuff sollte ich wohl nicht ran weil so ab 200°C auch Silikon schmelzen kann.
Hat da wer Erfahrung mit? Ansonsten versuche ich das einfach mal. -
Hab das Halteblech "95808020050 Halteblech Bugspoiler" vom Fachman geschweist bekommen, leider ists schon wieder gebrochen.
Kennt Ihr in CH einen guten Lieferanten für Ersatzteile? In DE soll das Ersatzteil um 60€ zu haben sein. Geht ja noch so, das Schweissen hat ne Kiste Moretti gekostet.
Add: Ist schon bestellt, hat sich erledigt. Wobei n Tipp für nen guten Lieferanten natürlich immer willkommen ist.